GreenBullChina straw factoryGet a quote
English

Wall thickness: the spec missing from most straw orders

Two straws can share a 6 mm outside diameter and differ by a quarter of the material. How to write gram weight on the order and check it on arrival.

A 6 mm straw is not one product. Two cartons can measure 6.0 mm across the outside and still differ in the wall, one at 0.4 mm and one at 0.5 mm. The second uses about 23% more material, bends close to twice as stiffly, and feels different the moment it goes into a cold drink. A purchase order that says 6 x 200 mm has not specified the straw yet.

Wall thickness is outside diameter minus inside diameter, divided by two. On a straight-cut straw you can read it with a caliper across the cut end, but the knife collapses the edge, and on paper straws the reading comes out thin. The number that survives a shipment and settles an argument is weight.

A thicker wall narrows the bore

At 6 mm outside and 0.4 mm wall, the inside diameter is 5.2 mm. Go to 0.5 mm and the bore drops to 5.0 mm, which cuts the flow area by about 8%. For a drink you pull through the straw, bubble tea or a smoothie with fruit pulp, adding wall makes the cup harder work. If you need stiffness and flow, the answer is usually 8 mm, not a heavier 6 mm.

Weigh 100 pieces, then do the arithmetic

Use a 0.01 g scale. Take handfuls from three places in the carton, count out 100 straws, weigh them, divide by 100 for grams per piece, multiply by 1000 for grams per thousand. Paper straws should sit in the same room for a day before weighing, because paper takes up and gives off moisture; compare samples that have rested for the same time, or you are measuring the weather.

Here is a worked example. A 6 x 200 mm PP straw with a 0.45 mm wall has a wall cross-section of 7.85 mm squared. Times 200 mm gives 1,570 cubic mm, times a PP density of 0.90 g per cubic cm gives about 1.41 g per piece, or 1,410 g per thousand. If the same straw weighs 1.56 g, the wall is nearer 0.5 mm. If a supplier quotes 1,300 g per thousand, question the wall before you question the scale.

On paper straws the wall hides in the ply count

A three-ply and a four-ply paper straw can be made to the same outside diameter. The four-ply one has more paper, a smaller bore, and holds up longer in a drink. Without cutting one open, grams per thousand is the quickest way to tell them apart. That is why a gram figure on the order does more work than the word heavy duty, which means something different in every factory.

What to put on the purchase order

Our natural straws run 6 x 190, 6 x 230, 8 x 200, 8 x 230, 12 x 200 and 12 x 230 as stock sizes, one carton minimum. Changing the wall does not need a new mould. It changes the paper width on a paper line or the wall thickness on an extrusion line, so the lead time follows the production schedule rather than tooling.

FAQ

Can you make a 6 mm straw stiffer without changing the outside diameter?

Up to a point. Going from 0.4 to 0.5 mm wall nearly doubles bending stiffness and takes 0.2 mm out of the bore. Past 0.6 mm on a 6 mm straw, drinks with pulp become hard to pull, and moving to 8 mm is the more practical answer.

How do I check wall thickness without a lab?

A 0.01 g scale and 100 pieces. Cut one straw and measure the section with a caliper as a cross-check. If the two numbers disagree, look at the cut edge first, because a crushed edge reads thin.

What is the minimum order if I want to test a heavier wall?

One carton. Running 2,000 pieces through a busy weekend tells you more than a sample card, and the carton weight lets you check the gram figure on your own scale.

Straw diameter and length chart →

Send the diameter, the length, and either the grams per thousand you need or the drink the straw has to handle. We will come back with a wall recommendation and the net weight per carton, so the quote can be checked on a scale when the goods arrive.

Inquiry

Address: Building 4, Leliu Jin Zhifei Garden, Shunde District, Foshan City